Posted on November 29, 2012May 12, 2013 by The Engineer — 1 Comment

Brightwell Brightstar II BSL4 Dosing System

Here is an old chemical dosing system for industrial washing machines. These units are 4-pump models, with dual pumpheads. The motors are reversed to operate alternate pumps in the same head.

From 2006, this is a fairly old unit, and made in the UK.

Main controller PCB, with interface to the power electronics via the ribbon cable, an external serial port for programming to it’s left. Powered by an ST microcontroller. The LCD is below this board.

Main power supply, sense input & motor driver boards. The PSU outputs +5v, +12v & +24v. The inputs on the lower left connect to the washing machine & trigger the pumps via the programming on the CPU. The motors are driven by L6202 H-Bridge drivers from ST.

Motor & gearbox assembly on the back of the pumphead. These are 24v DC units with 80RPM gearboxes.

UPDATE:
As it seems to be difficult to find, here is the user manual for this unit:
[download id=”5557″]

Posted on September 27, 2012 by The Engineer — Leave a comment

Update!

Well things have been hectic over the past couple of months.

With a new job & a new addition to the family I’m not getting much time to update the site, however there are a few things on the way!

More Raspberry Pi stuff will be arriving soon, running the GPIO with a web interface.
I found a fault with Dell servers that I’ve managed to fix without having to replace some very expensive parts! This might be of interest to people with such servers, more info to come soon!

Posted on July 14, 2012 by The Engineer — Leave a comment

ModMyPi Raspberry Pi Case

Finally, some protection for my Raspberry Pi! The PCB fit is slightly loose, but that was quickly sorted with the application of a couple of spots of hot glue in the corners.

Unfortunately, the case is a couple of mm too small to fit the main board from the Pico Projector inside, so I won’t be butchering that into the case with the Pi as yet. What is required is an interface to the display engine from the Pi’s DSI interface.

The pi all boxed. up. The only thing that this case would now require is a lightpipe to direct the LED’s light to the openings in the case, as they are very difficult to see at present.

Posted on July 8, 2012 by The Engineer — Leave a comment

Cisco 2G Fibre Channel SFP Module

2G Fibre Tranciever — 2G Fibre Transceiver

Here is a 2Gbit Fibre Channel transceiver from Cisco Systems in SFP module format.

Here the shield has been removed from the bottom of the module (it just clips off). The bottom of the PCB can be seen, with the copper interface on the left & the rubber boots over the photodiode & 850 nm laser on the right.

Here the PCB has been completely removed from the frame, the fibre ends slide into the rubber tubes on the right.

Top of the PCB, showing the chipset. There are a pair of adjustment pots under some glue, next to the chipset, presumably for adjusting laser power & receive sensitivity. The laser diode & photodiode are inside the soldered cans on the right hand side of the board, with the optics required to couple the 850nm near-IR light into the fibre.

Posted on December 21, 2011December 21, 2011 by The Engineer — 1 Comment

MSR605 3-Track Magnetic Stripe Writer

This unit was bought from eBay to experiment with Magnetic Stripe cards, for little money. This unit is capable of reading & writing all 3 tracks, & both Hi-Co & Lo-Co card types.
Interfaced to a PC through USB, this has a built in PL2303 USB-Serial IC & requires 3A at 9v DC to operate.
The 3 Indicator LEDs on the top of the unit can be toggled by the included software for Power/OK/Fault condition signalling.

Bottom of the unit with the model labels.

Closeup of the model label & serial number.

Here the bottom cover has been removed, showing the main PCB. The pair of large ICs bottom center interface with the magnetic heads. The IC above them has had the markings sanded off.

Closeup of the Prolific PL-2303 USB-Serial converter IC.

Here the connections to the R/W heads are visible, current limiting resistors at the left for the write head, a pair of signal relays, a pair of optoisolators & a LM7805 linear voltage regulator.

Here is the trio of indicator LEDs on a small sub-board.

The PCB has been removed from the main frame here, the only component visible is the rotary encoder.

The rotary encoder has a rubber wheel fitted, which reads the speed of the card as it is being swiped for writing. This allows the control logic to write the data to the stripe at the correct rate for the speed of the card. This allows the unit to write cards from 5-50 inches per second speed.
The Write head is directly behind the rubber pressure roller.

Here you can see the R/W head assembly. The write head is on the right, read on the left. When a card is written to, it immediately gets read by the second head for verification.

The drivers for this unit are also available here: Magcard Writer Drivers

Posted on October 3, 2011August 3, 2017 by The Engineer — 5 Comments

Rare Veroboard Design Tools – Stripboard Magic

Stripboard Magic

Stripboard Magic is a Windows application for designing PCB layouts on stripboard (aka prototyping board, aka Veroboard). It was released by a British company called Ambyr which ceased trading a long time ago.

The interface is a quite primitive and a little strange but the program is functional even on Windows XP. It also works great under wine in Linux, at least with version 0.9.38 and above as this is all I have checked. It should probably work on older versions too. I haven’t tried it on Vista though.

It can be a handy program when called upon and I have successfully used it a few times when throwing together random small circuits. Due to the interface I would imagine it to be a bit clumsy for very large circuits. The biggest gripe I have with it is the inability to change the orientation of components on the board, so some circuits tend to be slightly larger than they need to be.

I downloaded a copy of Stripboard Magic 1.0 back in the 90’s and recently just found it lying about on my computer. As I would consider it to well and truly be abandonware and as it seems to be a little sought after by some hobbyists I have provided a link to download it below.

[download id=”5624″]

Here are some screenshots showing the schematic view (top) and board layout view (bottom):

Stripboard Designer

Another hard to find app these days is Stripboard Designer, mirrored here for people who wish to use it.

[download id=”5626″]

[download id=”5628″]

Posted on March 6, 2011February 11, 2011 by The Engineer — Leave a comment

Cheap Ball Mouse

Cheap old style ball mouse. PS/2 interface.

Top removed from the mouse, the ball fits in the gap in the centre. The slotted discs are visible which contact the ball & move relative to the surface the mouse is on.

PCB removed from the shell. Pairs of IR LEDs & Phototransistors make rotary encoders with the slotted discs. The microswitches read the mouse buttons & wheel.
IC in the centre interfaces with the PC over a PS/2 connection.

Posted on February 20, 2011February 10, 2011 by The Engineer — Leave a comment

Garmin eTrex

Pocket sized GPS navigator. Here is shown the greyscale dot matrix LCD.

Serial interface on the back of the unit. Pinout from left is +3v, Rx, Tx, GND.

PCB Removed from the casing. RTC backup battery in the centre of board, CPU & flash ROM on the left. GPS chipset is under the shield on the right.

Front of the PCB, GPS antenna on the right, LCD panel left.

LCD folded back from the PCB. Driver IC can be seen attached to the ribbon.

LCD Panel backlight. Requires 200v AC at 20kHz to glow green.

GPS chipset with the shield removed.

Posted on February 10, 2011February 4, 2011 by The Engineer — 1 Comment

Hauppauge WinTV USB

Here is one of the first USB tuners that was available from Hauppauge Computer Works. Totally analog tuner of course, this model required 2 cables – a USB interface & a sound cable for the audio output of the tuner.

A/V connections.

For those who are interested. Here is the label with the model details.

Connection to an external antenna.

Bottom of the PCB.

Top of the PCB showing the USB interface IC (top left), cache memory (top right) & the main tuner assembly.

Posted on October 20, 2010 by The Engineer — 1 Comment

Co-Op Bank Card Reader

This is a little security measure you get with Internet Banking with the Co-Op, generates codes to confirm your identity using your bank card. About the size of a pocket calculator, this is the keypad & screen.

The rear of the unit, the card slots into the top, manufactured by Gemalto Digital Security.

Outer back cover removed, showing the 8 contacts for the chip on the bank card, the 2 contacts below that switch on power when a card is inserted. Power comes from 2 lithium coin cells in the compartment on the lower left.

PCB removed from the casing, showing the internal components. Two large pads at top left are battery connections, while the only IC on the board is the main CPU, under the card connector. 6MHz oscillator & 32Khz crystal on board for processing & timekeeping. LCD screen connection at far right.

Reverse side of the PCB, with the keypad contacts. LCD on right, with programming interface pads at side of keypad.

Posted on September 23, 2010 by The Engineer — Leave a comment

Belkin F5U021 4-Port USB Hub

This is an old USB 1.1 hub that was recently retired from service on some servers. Top of the unit visible here.

Bottom label shows that this is a model F5U021 hub, a rather old unit.

PCB is here removed from the casing, Indicator LEDs along the bottom edge of the board, power supply is on the left. Connectors on the top edge are external power, USB host, & the 4 USB outputs. Yellow devices are polyswitch fuses for the 500mA at 5v each port must supply.

This is the USB Hub Controller IC, which is a Texas Instruments TUSB2046B device. Power filter capacitors next to the USB ports are visible here also, along with 2 of the polyswitches.

The power supply section of the unit, which supplies regulated 5v to the ports, while supplying regulated 3.3v to the hub controller IC. Large TO-220 IC is the 5v regulator. Smaller IC just under the power selector switch is the 3.3v regulator for the hub IC. The switch selects between Host powered or external power for the hub.

Posted on September 23, 2010 by The Engineer — Leave a comment

USB Flash Drive

Here is a cheap chinese made flash drive given out for free by Westlaw UK. Capacity 512MB

Here is the PCB removed from the casing, USB connector on the left, followed by the clock crystal for the flash controller, a CBM2092, which is a Chipsbank part. 512MB flash memory IC, unknown maker. Access LED on far right of the board.

Posted on August 26, 2010 by The Engineer — Leave a comment

Nokia 7110

Another phone from the mid 90s. This is the nokia 7110.

Here the slider is open showing the keypad.

Here the battery is removed, a Li-Ion unit.

The battery cell & protection circuit removed from the casing.

This is the rear of the PCB removed from the housing. Data & charging ports on the right hand side f the board.

Front of the PCB with the RF sections at the left hand side & the keypad contacts on the right.

Closeup of the RF sections of the board, big silver rectangular cans are VCO units.

Closeup of the top rear section of the PCB, with SIM cnnector, battery contacts, IR tranciever at the far left. Bottom centre is the external antenna connector.

The logic section of the board, Large chip is CPU, to right of that is the ROM storing the machine code. Other chips are unknown custom parts.

The Mic & the loudspeaker removed from it’s housing.

LCD from the front of the unit, SPI interfaced. Flex PCB also contains the power button, loudspeaker contacts & a temperature sensor.

The scroll wheel removed from the front housing.

Tiny vibration motor removed from the rear housing, alerts the user to a text or phone call.

Posted on July 29, 2010August 1, 2010 by The Engineer — Leave a comment

Western Digital 160GB 2.5″ HDD

This is a Western Digital drive recently removed from my laptop when it died of a severe head crash.
Top of drive can be seen here.

Here the cover has been removed from the drive, showing the platter, head arm & magnet. Yellow piece top left is head parking ramp.

The head assembly of the drive is shown here. The head itself is on the left hand end of the arm in the plastic parking ramp. The other end of the arm holds the voice coil part of the head motor, surrounded by the magnet.

Bottom of drive, with controller PCB. SATA interface socket at bottom.

PCB removed from bottom of drive. Spindle motor connections & connections to the head unit can be seen on the bottom of the drive unit.

Controller PCB. Supports the cache, interface & motor controller ICs.

Closeup of the motor driver IC, this controls the speed of the spindle motor precisely to 5,400RPM. Also controls the voice coil motor controlling the position of the head arm on the platters.

Interface IC closeup. This IC receives signals from the head assembly & processes them for transmission to the SATA bus. Also holds drive firmware, controls the Motor driver IC & all other functions of the drive.

Cache Memory IC.